GAME SUPPORT

Service / Tech Support:
815-541-4940
service@spookypinball.com







HALLOWEEN

Code Update V1.05

Update Requirements:

-Use a USB drive with 4GB to 32GB of storage. Do not exceed these bounds.

-Do NOT use a Mac system to format your USB. Use Windows 7/10, and format as FAT32.

-Do NOT pull the USB immediately after files copy. Right click on the USB drive from the ‘Computer’ window, and select ‘eject’. Windows will tell you if it’s ok to remove the USB.

-if your download includes (1) or some other number, rename the file to code_H78.pkg

-Skipping any of these actions can and will cause the game to run in an unexpected manner, or not at all.

V1.05 01/JAN/2022

UPDATE midscoop – blinks fast when about to eject
UPDATE left/right lifter lights blink fast
UPDATE mode totals at end of modes
UPDATE selected mode selection could change when flippers were re-enabled
UPDATE extra ball added to blood store, costs 25
UPDATE lower right ball lock removed drop target position check from the lock routine this is to help with fail lock attempts
typo in a key used for counting visited modes
UPDATE knocking down drop targets on skillshot no longer reset
UPDATE house drop target area blinks purple with mike health at zero
UPDATE death in drivers seat, slow center ramp shot wouldn’t count
UPDATE when in a main mode, side modes now cycle properly
ADDED new stalker mode

 

 

 

 

 

 

 

Ultraman Kaiju Rumble!

Code Update V1.05

Update Requirements:

-Use a USB drive with 4GB to 32GB of storage. Do not exceed these bounds.

-Do NOT use a Mac system to format your USB drive. Use Windows 7/10, and format as FAT32 / 32kb.

-Do NOT pull the USB immediately after files copy. Right click on the USB drive from the ‘Computer’ window, and select ‘eject’. Windows will tell you if it’s ok to remove the USB.

-if your download includes (1) or some other number, rename the file to code_UM.pkg

-Skipping any of these actions can and will cause the game to run in an unexpected manner, or not at all.

V 1.05 01/JAN/2022

UPDATE bemular super ready voice would repeat itself
UPDATE pull down mech was missing from coil test
UPDATE selected mode selection could change when flippers were re-enabled
UPDATE Gomora spelled wrong in mode select
UPDATE skillshot to rightscoop was not registering missed skillshot event
UPDATE extra ball added to spacium store, costs 25
UPDATE lower right ball lock was playing the clip and audio on a 1 second delay
UPDATE lower right ball lock removed drop target position check from the lock routine this is to help with fail lock attempts
UPDATE typo in a key used for counting visited modes
UPDATE knocking down drop targets on skillshot no longer reset
UPDATE ragon, slow center ramp shot wouldn’t count
UPDATE when in a main mode, side modes now cycle properly
ADDED new dada mode

Manual coming soon







RICK & MORTY

Code Update

How-to update video

 

 

 

 

 

 

 

 

 

 

 

 

 

ALICE COOPER’S NIGHTMARE CASTLE

Code Update

ACNC Manual

 

 

Update Notes:

v1.1.0.5
23/MAR/2021
System – log file was not clearing after an update
System – log file would copy to usb on audit dump but did not clear a flag that could prevent the game from starting
system – log file will now clear if it gets larger than 100MB
General – main screen mini map now reflects difficulty
General – mini map shows green rooms indicating a weapon is available
General – path with weapon in next room will strobe green to match color on mini map
Frank – some animation, sfx, shaker changes

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

TOTAL NUCLEAR ANNIHILATION

Documentation

Code Updates

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

America’s Most Haunted

Switch matrix chart

Lamp matrix chart

Apron cards/instructions

Wiring/board chart

Game setup instructions

Servo replacement video

Code Updates

ALSO… To finish off your code update, go into the game menu and reset everything to Factory Defaults… then adjust your coil strengths as needed. Zero is low power, 9 is high.

Rubber Sizes:

– 2.5″ rubber

2 – 3/16″ ID rubber (small purple posts)

4 – 3/8″ OD rubber (small spike posts)

4 – 3/8″ ID rubber (star posts)

4 – post sleeves 1 1/16″

2 – Standard Flipper rubber

Mylar placement:

 

Rob Zombie’s Spookshow International

Wiring/board chart

Lamp matrix chart

Switch matrix chart

Apron cards/instructions

Code update instructional video

Code Updates – V026 – See below for update process

-Do NOT use a Mac system to format your SD CARD. Use Windows 7/10.

-Do NOT drag the contents of the zip file directly to the SD CARD. You must extract the zip file to a folder on your computer first, then you may drag the files from that folder to the SD card.

-Do NOT extract the zip file directly to the SD card.

-Do NOT pull the SD card immediately after files copy. Right click on the SD card from the ‘Computer’ window, and select ‘eject’. Windows will tell you if it’s ok to remove the SD card.

-Skipping any of these actions can and will cause the game to run in an unexpected manner, or not at all.

Rubber sizes:

3 – 2 1/2″

1 – 3″

3 – 3/8″ OD

3 – 1 1/16″ post sleeves

1 – 1 1/4″

1 – 3/4″

1 – 2″

2 – 3/16″

9 – 3/8″

 

Mylar Placement: